
29 000:-(SEK)
Kategori: Högtalare Västra götaland/Partille: Visa på karta
Mats Andersens avknoppning på Qln heter Strandberg Audio.
Nu finns tillfälle att köpa ett begagnat par i matt valnötsfinish.
En 2-vägs golvhögtalare med åttatummare i basen.
Prisvärd och mycket välljudande även sett till nypriset (65'000 kr).
Passa på...
Introduction The Strandberg C50 is a classical designed floor standing speaker with the latest drive units technology. The goal is to make an uncomplicated sound that is easy to listen to that respond well to the smallest input signal. To achieve this we use one larger mid-woofer with low mass, instead of many small drive units. In this way we get more physical feeling of lower frequency than just the deep tone. The balance between what we hear and frequency measurements will be more correct. In other words we get more body in the sound. Drive units with light cone is also easy to drive with a small amplifier. The larger cabinet size will make low cone mass mid-woofer breathe natural with less compression. Then we will have deep clear un compressed natural bass.
Design details
Cabinet The cabinet is tuned to make a natural roll-off without any ringing in step response. Cabinet are made of MDF-board with internal damping pads for minimising cabinet material resonances. Cabinet is heavily braced to give stiff cabinet and the damping pads make it non resonant so the cabinet don’t store sound in the time domain. Natural wool is used for internal acoustic damping because it sond best and have a wider frequency damping of the internal sound. It is loose packed so we don’t store sound in the damping material. We use minimum damping material and apply it where it do the most use, in centre and middle of the cabinet were air speed is at it maximum. Then we can apply minimum damping material to achieve maximum damping of the internal sound.
Crossover The 2 way crossover is hardwired with high-end Mundorf capacitors and baked air coils to avoid any internal component and filter resonances. The secret with crossover design is to make the driver to play together without pushing any drive unit over the comfort zone. So we have to consider the cone area together with drivers material behavior. The result is seamless transition between mid-woofer and tweeter over the crossover point and throughout the entire frequency range.
Drivers The 8” mid-woofer and tweeter drivers have been specifically selected and custom developed by industry renowned driver manufacturers and offer the latest in 21st century advanced driver technology. The 8” mid-woofer driver with titanium voice coil former and its built-in copper rings in the magnet system offers high symmetric drive suppressing intermodulation distortion. Low losses and large window in the chassis to reduce reflection air noice resulting in industry leading high-end voice handling and astonishing micro/macro dynamics in its hole frequency range. Likewise the 30mm wide surround waveguide tweeter offers time alignment superb vocal rendition and excellent imaging at listening positions. The 30mm tweeter is a perfect combination to the 8″ mid-woofer. With the lager cone area it meets the mid-woofer in natural way and make the two driver behave like one music source for the listener. Tweeters large surround, built-in copper ring and textile dome diaphragm provides a flat frequency response above 30 KHz. Large rear acoustic chamber give low compression and move tweeter system resonance far from crossover point.
Cables and speaker connectors Internal cabling are our own special design cable. Special designed for use as internal speaker cable . All components are carefully hand selected and individually tested for any deviances. WBT pure copper NexgenTM pole screws are used with grip-friendly screws.
Impedance: 8 ohms Amplifier recommendations: 25-150 Watt RMS Tweeter: 30mm wave guide, wide surround, soft dome Woofer: 200mm mid-woofer, paper cone Sensitivity: 89 dB SPL 1 Watt 1m Low frequency performance: -3dB 35Hz Cabinet: High density board with damping pads inside Terminal: WBT Single wire Dimensions (HxWxD): 1020x250x300 Weight: 29,0 kg each Finish: Walnut matte
Hos Hifi Puls AB kan du köpa direkt via hemsidan och betala med kort, räntefri avbetalning via Svea eller på faktura.
Eller köp via butiken i Sävedalen.
Fri frakt inom Sverige
Alltid 3 månaders garanti på begagnade produkter.
Liknande annonser i Högtalare